Other

Replacement top subassemblies are compatible across Cane Creek 110-, 40-, and 10-Series headsets with the same SHIS values. - Bearings not included

Replacement inserts for Thudbuster G4 suspension seatposts. - Cane Creek LT G4 Elastomer Insert - Medium

Replacement inserts for Thudbuster G4 suspension seatposts. - Cane Creek LT G4 Elastomer Insert - X-Firm

Replacement inserts for Thudbuster G4 suspension seatposts. - Cane Creek LT G4 Elastomer Insert -Soft

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Air Spring Volume Reduction Kit - Cane Creek Kitsuma 5mm Air Stroke/Volume Reducer

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Cane Creek crown races are interchangeable between headset series.

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Replacement seals for servicing Cane Creek rear shocks.

The Ancora Expansion Plug is designed for use with carbon steerer tubes. Machined Aluminum expansion wedges paired with a knurled sleeve ensure a secure fit with the correct preload amount. - Accepts any standard preload bolt and top cap (sold separately) - Insertion length: 46mm - Contact surface length: 38mm

Replacement clamp kit for Thudbuster G4.

Replacement stainless steel cartridge bearings for Cane Creek 110 headsets - 38mm, 41mm, and 42mm are sold in pairs - 52mm sold individually

A higher quality spring greatly improves the performance of your coil shock. VALT springs from Cane Creek are much lighter than traditional steel springs while pushing the boundaries of performance and durability. - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks - Also compatible with Manitou, Marzocchi, XFusion, ELKA/MRP, BOS and DSP - Compatible with Fox coil shocks with required spring clip adaptor

A higher quality spring greatly improves the performance of your coil shock. VALT springs from Cane Creek are much lighter than traditional steel springs while pushing the boundaries of performance and durability. - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks - Also compatible with Manitou, Marzocchi, XFusion, ELKA/MRP, BOS and DSP - Compatible with Fox coil shocks with required spring clip adaptor

Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks

Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks

Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks

The performance of your shock is directly related to the quality of your spring. VALT springs offer a significant weight reduction over standard steel springs. Riders can enjoy the performance benefits of coil shocks without the weight penalty. Progressive-Rate VALT coil springs are designed and tuned by Cane Creek's engineering team to provide riders with a true rise-in-rate spring curve. The Progressive-Rate VALT springs maintain the sensitivity and "set it and forget it" mentality of a traditional coil set up, but with the progressiveness and ramp up that hard-charging riders and many frame designs demand. Progression begins at 50% into the stroke of the spring. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 24mm - Width: 5mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 26mm - Width: 5mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 28mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 30mm - Outer Diameter: 42mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

Improve the performance of your 11-speed Shimano rear derailleur with pulleys that reduce friction and increase bearing life. Ours are designed to work with less drag, adding to the power transmitted to the rear wheel. - Uses low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. - A set consists of differing upper and lower pulleys: they are marked as such and have directional arrows etched on them so you know exactly how to install them. - These pulleys are compatible with all Shimano 11-speed rear derailleurs except XT or XTR. - The kits come with CeramicSpeed oil in a 15ml dropper bottle. The bearings come pre-oiled. In the box: - 2 x 11-tooth pulley wheels - 4 x spacers - CeramicSpeed Bearing Oil in 15 ml dropper bottle - Sticker sheet

This is an updated version of the Oversized Pulley Wheel System for Shimano 9100/9150 and 8000 SS/8050 SS. This new design has an integrated stop tower for easier mounting. The CeramicSpeed Oversized Pulley Wheels System has been proven to be the fastest pulley system in the world, providing energy savings starting at 2.4 watts compared to standard Shimano systems. The OSPW System for Shimano 9100/9150 and 8000 SS/8050 SS is an industry-leading product, chosen by many of the world's leading cycling teams and professional triathletes. It features a 13-tooth upper pulley wheel and a 19-tooth lower to provide absolute optimization of the rear derailleur, and these oversized aluminum pulley wheels come fitted with either standard or coated CeramicSpeed Bearings: your choice. The Shimano 9100/8000 OSPW system is compatible up to a 32 tooth cassette for both Dura Ace & Ultegra derailleurs The typical overall power savings of the OSPW System for Shimano 9100/9150/8000 is 30%-60% over a stock setup. The oversized pulley wheels have lifespan that is 3-5 times longer than the commonly used standard pulleys on the market. Please note: The OSPW System for 9100/9150 and 8000 SS/8050 SS is NOT compatible with Ultegra 8000-GS or 8050-GS (medium cage) derailleurs, nor with the clutch-equipped Ultegra RD RX800 & RX805. Choose CeramicSpeed's OSPW X for Shimano RX800/805 for a compatible RX800 & RX805 version. For a compatible upgrade for Ultegra 8000-GS or 8050-GS choose their Pulley Wheels for Shimano, 11s NW. In The Box: - A complete 13-tooth/19-tooth OSPW System - CeramicSpeed Bearing Oil in 15ml dropper bottle

Developed and designed entirely by CeramicSpeed, the Oversized Pulley Wheel System for Campagnolo is advanced for the optimization of bike performance. Everything from bearings to the cage is made from the highest quality materials. The oversized aluminum pulley wheels are fitted with standard or coated CeramicSpeed Bearings, which reduce friction to the minimum. The 13-tooth/19-tooth OSPW for Campagnolo provides 40% lower friction over a standard 11-tooth Campagnolo pulley wheel and fits up to a 32-tooth cassette. The OSPW for Campagnolo is compatible with all Campagnolo electronic rear derailleur (EPS) and all rear derailleurs with a mounting sleeve—no matter the age and model. At this point, this OSPW System is not compatible with the Campagnolo 12-speed Record and Super Record derailleurs. The OSPW for Campagnolo is compatible with: - Record mechanical - Record EPS - Super Record mechanical - Super Record EPS - Potenza mechanical - Chorus Please note, some models of Campagnolo rear derailleur, including all EPS models, do not feature a B-limit adjustment. While this product is still compatible with those derailleurs, it may not be possible to fit a 32 tooth cassette successfully on some bikes. When travelling, please remember to dismount your entire rear derailleur with an Allen key, as the OSPW System will not safely fit in most bike travel bags and could be damaged if left on. In The Box: - Oversized Pulley Wheel System - CeramicSpeed Bearing Oil in 15ml dropper bottle - Sticker sheet

Developed and designed entirely by CeramicSpeed, the Oversized Pulley Wheel (OSPW) System for Shimano 9000/6800 provides the ultimate optimization of your bicycle's drivetrain. This OSPW System features a set of 17-tooth aluminum Pulley Wheels housed in a specially designed polyamide (PA) and carbon cage. The upper and lower 17-tooth oversized aluminum pulley wheels come fitted with either standard or coated CeramicSpeed Bearings. The Oversized Pulley Wheel (OSPW) System is the product of choice by many of the world's leading cycling teams and triathletes. This specific system is compatible with Ultegra 6700/6770/6800/6870 mechanical and Di2 rear derailleurs and Dura Ace 7900/7970/9000/9070 mechanical and Di2 rear derailleurs. It is not compatible with Shimano Dura-Ace 9100/9150 and Ultegra 8000 series rear derailleurs. For those rear derailleurs you will need a OSPW System for Shimano 9100 series. The system is compatible with up to a 28-tooth cassette on most bikes, depending on derailleur hanger. The typical overall power savings of the OSPW System for Shimano 9000/6800 is 30%-60% over a stock setup, and the oversized pulley wheels have a lifespan that is 3-5 times longer than the commonly used standard pulleys on the market. In The Box: - A complete 17-tooth OSPW System - CeramicSpeed bearing oil in 15ml dropper bottle